chevron_left

メインカテゴリーを選択しなおす

cancel
CBX-LALALA
フォロー
住所
未設定
出身
未設定
ブログ村参加

2024/05/29

arrow_drop_down
  • FCR Tuning – Jet needle changed to 90FTN. I was concerned about the straight diameter – 22/11/15

    This is a test run after changing the jet needle of the CBX FCR. The purpose is to check whether the straight diameter of the jet needle is good or bad at low throttle opening. I have been selecting a jet needle for the slow jet 48 for a while now. As a result of the test run, the acceleration is so good that I don't want to touch it for a while.

  • FCR – The fuel line should be angled so that fuel can flow easily.

    CBX is a forced open/close type gasoline cock. About the fuel line Although it is a short path during the process of sending fuel from the gasoline tank to the carburetor, air may become trapped. It's not just the angle of the fuel line, but also the nature of the filter that makes it difficult for fuel to flow.

  • FCR Tuning-Adjust the air screw with a digital tachometer-22/11/10

    Fine adjustment of the air screw and pilot screw positions. Until now, we had determined the position of the air screw based on a test run. Of course, I also use the air-fuel ratio meter as a reference. The position of the air screw is determined based on a test run. I purchased a digital tachometer.

  • Notes on changing FCR slow jet

    Since the CBX1000 has 6 carbs, the number of jet changes is 6 times that of the SR, and 1.5 times that of a 4-cylinder motorcycle. It's a pain. When purchasing a new jet, it costs 6 times more than an SR. I don't regret it too much since it's money I'll be spending on my hobby, but it's better if it doesn't cost anything.

  • FCR setting-Jet needle replacement-Up change-22/11/08

    This is the FCR setting. Current jet needles have a special thread count that sharpens up. It should be 90FXM#3=90FTM#1. I haven't tried it, so I don't know, but it should probably be the same. I'll check it out when I have some free time.

  • FCR Tuning – Tuning throttle opening from 1/16 to 1/8 – 22/11/06

    Regarding the current FCR tuning of CBX, I was concerned about the lower throttle opening. It's not a good idea to get caught up in the air-fuel ratio meter, but a partial reading of 10.5 is around throttle opening of 1/16 to 1/8. It is unclear whether this condition is good or bad.

  • FCR Tuning – The number of clip stages of the jet needle is determined by the driving feeling

    You can enjoy changes in the driving feeling that cannot be seen only with lean or rich FCR influence range. When you wear an air-fuel ratio meter, you tend to look at the numbers and judge whether it's lean or rich.Considering the characteristics of engine revving, etc., there are some areas that are difficult to show in the numerical values. Simply put, you can change the number of clip stages one by one and try the number of stages that gives you the driving feeling you like.

  • FCR setting-Carburetor synchronization work-22/11/02

    I had time, so I did some synchronization work on the CBX's FCR carburetor. If you play around with the idling stop screw, you will notice a difference between the carburetors in groups 1, 2, and 3 and the carburetors in groups 4, 5, and 6, which is a concern. Recently, I have been focusing on setting the throttle to a low opening.

  • FCR Tuning – Slow Jet Selection – Start with the pilot screw back at about 1.0

    You should be careful when choosing a jet needle. Even if the condition is good when the throttle opening is low, the effect may appear as the throttle opening is increased. The number of CBX's FCR jet needles at the time of shipment is 90FXM#3. The cut-up is special.

  • FCR Tuning – Cold Startability – Air Screw and Pilot Screw Adjustment – 22/11/01

    This is a post about the FCR setting of CBX. The other day, I adjusted the air screw while watching the idling with a digital tachometer. I didn't tighten the pilot screw to rich or lean, and I didn't return the air screw for about 15 minutes after the maximum opening.

  • Changed the FCR acceleration pump diaphragm. Visual inspection is important. Changes in total discharge volume are difficult to understand

    I am trying to replace the FCR standard accelerator pump diaphragm with the Kawasaki KX250 diaphragm. There is a dot in the center of the accelerator pump that suppresses the movement of the accelerator pump diaphragm. As for how much of a change there is, you can feel the change when you see it for the first time.

arrow_drop_down

ブログリーダー」を活用して、CBX-LALALAさんをフォローしませんか?

ハンドル名
CBX-LALALAさん
ブログタイトル
CBX-LALALA
フォロー
CBX-LALALA

にほんブログ村 カテゴリー一覧

商用