今回は、冷媒ガスを回収するボンベが、なかったので、suction とdischargeの両方を栓を閉めてからvrfシステムで室外機回収できる接続場所があったので、そこからから、1度、dischargeから冷媒ガスを取り除き、ゲージを通し回収マシーンを通り、回収しました。
現地で実際に使われる英語表現をこちらで、説明しつつ、日々の面白い体験等もこちらアップしていきます。
ニュージーランドで空調の仕事で、働いている日本人です。 私の働いている会社には、ニュージーランド人、イギリス人、インド人が主に、働いています。そこで使われる使える英語表現をこちらで、説明しつつ、日々の面白い体験等もこちらアップしていきます。
「ブログリーダー」を活用して、toshiさんをフォローしませんか?
今回は、冷媒ガスを回収するボンベが、なかったので、suction とdischargeの両方を栓を閉めてからvrfシステムで室外機回収できる接続場所があったので、そこからから、1度、dischargeから冷媒ガスを取り除き、ゲージを通し回収マシーンを通り、回収しました。
日立のvrfがエアコンが急に冷房が効かなく、調査してみるとエラーコードが51 communication between the inverter PCB and the outer unit PCB has failed. If error code 51 is displayed this indicates a fault in the inverter current sensor.ということでどうやらp
チラーが急にロックダウンしてしまった。Loss of oif of compresssor.というメッセージがエラーメッセージに出ていた。おそらくオイルが全て、エバポレーターの方に、移動してしまい、コンプレッサーの方にオイルがなくなり、潤滑油がないので、上手くコンプレッサーが作動し
今回は、ダイキンのvrfのインドアのファンモーターが作動しなくなったので、チェックしてみるとfaultメッセージがaj.Capacity setting error – The capacity or address setting is faulty. C3 – Abnormal water level sensor resistance – The water level sensor ha
when i check single phase compressor.check resistance compresor winding between pin.if will be 2オーム、1オーム、3オーム.~~~~~~~~~~~~next three phase compressor will all same number such as 0.4オーム、0.4オーム,0.4オーム
今回は、日立のvrfのエアコンが効かないとの事。エラーコードが48過負荷運転保護作動 冷媒過多、冷媒配管詰り、サイクル部品の異常などによる圧力上昇、 圧縮機異常(過負荷、ロック、過電流)という理由で室外機のファンが全く動いていないので室外機のコンデンサーファ
ダイキンのvrfシステムのエアコンが冷房の効きが悪いという事で冷媒のガス漏れと思い室外機を開けてみたら、ガス漏れサインが確かに触ってみると、ヌルヌルして冷媒ガスが漏れたのがわかりました。その上の部分のバルブしっかり締め、冷媒ガスを少し入れました。そして確
その理由は、コンデンスウオーターが、途中の配管部分で詰まっているために、high presureのフォルテイーメッセージが出て作動しなくなるべくました。おそらく新しく設置した時、プレッシャーを設定の調節がうまくできていなかった可能性がある。今回、こちらには、ストレイ
まず、一度、メインの室外機のメインスイッチを切り 、また、スイッチを入れ。設定番号が、1.1.1になってるか確認。それが、確認できたら、設定を2.3.1にしてsw4のボタンを4秒押す。その後、U1.F16のメッセージがでた後、PFFのメッセージが出たら、すべてのバブルが開放され
当然、ゲージでガスのプレッシャーを調べれば、ガスが不足してるかわかります。その他にもコンプレッサーにつながる配線の電流がどのくらい流れかでガス不足の可能性mもわかります。こちら、冷房で作動してる場合は、10アンペアという記述が室外機にしてまりました。試しに冷
こちらでスーパーヒートを計算してみました。 Suction line のプレシャーは、53psiでこの場合は、Dew設定で4度になり実際の温度8度から4度を引いてスーパーヒートは、4kになります。
Some of the Air Duct was state of becoming deterioration due to a long time use it.So we replaced New Air.duct.Old Duct head and New Duct head. I connected ducting by ream&impact driver.
これが、コンプレッサーマシーンフェイリアーで、こちらの赤色の部分が壊れた状況です。
エアコンが冬場に温まらないって言われたので確認に行きました。2台がそういう状態で、1台めは、暖房モードでviberサイドのdischarge 側は、30psi. suction 側は、0でした。ということでガス漏れが原因というのが。わかりました。もう一つは、ガスは、しっかりあるのをチ
There are four aircon inside of A restaurant.However,one of aircon unit's wall contorol lacation is inside of kitchen area.(normally kitchen area is always warm.That's why always this unit 's supply air area Is very cold.So,first ,I did main settings tem
本日は、あるオフィスのミーティングルームのエアコンの効きがよくないとの事で確認に行きました。どうやら温度センサーの設定場所がそのミーティングルームの外側の少し暖かい場所に設置してある室内機の吸い込み側になっていたので、新たにミーティングルームのウオールコ
One of the compressor of vrv is mechanical failure.So I have to replace the compressor of unit.So I did reclaimed the refrigerant gas .I checked weight of cylinder. It was 12.7k weight. 21.6 L is maximum capacity of this cylinder.So normally it can put i
This time,I did install drain pipe of ac.ーI connected drain pipe from unit.I used elbow pipe to connect drain pipe.It was a little be long.So.i cut it.Finally,I connected small elbow.
こちらのvrvのガス回収、ということでvrv をrecoverly モードにします。mmBS1を6秒、押し続ける。そして、set 21回押し、>returnを1回、>setを1回Returnを2回 押すと、recoverlyモードになり、バルブが開く音が確認できます。
Vrvのシングルユニットの温度センサーが正常に機能してるか確認する方法として、その時の実際の温度と温度センサーの抵抗値をチェックする事により、正常に機能してるか確認できます。
I found out one of the grill flame was wobblingafter clean of the grill of Exhaust air ducting line.So I fixed it.It is pretty rusty some of the bottom of the grill.So I did brushing with impact driver.I sprayed rust converter to rusty area.I painted the
One of the toilet extracter ducting line was tearing off near the Diffuser area.So I was planning to connected together with Joiner ring.Firstly I cut tear off area of ducting line by nipper. I put on joiner ring near Diffuser area.And then I rolled
One of the fan belt was cracked of the package unit.So I replaced the new fan belt .Firstly,I switch off the power.Open the door of fanmotor area.Loosen the bolts on both sides of the base toChange the positin of height is a little lower and the belt ca
あるサイトでは、地下に2台、屋上に1台のチラーがあります。もしも屋上のチラーがfalty で使えない場合の裏わざとして、屋上のチラーをスイッチを切り、チラーパンプのスイッチを切り、supply とreturn の両サイドのバルブを閉めて、もう一つ、8階にある別々の場所にあるs
Today,some of my client asked airconIs not cooling,and sometimes,Tripp switch borad.So when I check this aicon,which is hydronic unit,I found burn out of end of the cable (terminal block) compressor .Just in case ,it might be grounded of this compress
本日は、一般のエアコンの故障を診断してきました。商業用のエアコンが4台あるうちの2台が冷房が効かないという事で診断してきました。1台目は、電気が室外機に来てますが、ファンも回らず、コンプレッサーも作動していないようでした。室外機のpcpボードには、電圧は、220
Temperature senser was faulty.So we replacedNew semser.Connected pc to do bindly viewMode.I put.mangnet to activate of new temperature Senser.Then click bindly of sener of pc.Yes.now working properly.
こちらのように1度以上の差がなければ、冷媒ガスrefigeration の量は、適量ある。
One of the evaporator water flow switchWas not working properly.So I replacedNew evaporator water flow switch.First I closed chiller water flow side valve &return side valve.IAfter attached crimp termina,I opened chill water flow&return valve. I setted
こちらで、Evaporator water flowが no flowというのがわかります。構造は、こんな感じこちらは、no flow の状態。そして水の流れがあるとこのように開く感じになります。これでイメージがわくと思います。
It was not really cooling 8th floor of the A buildding.So when I checked BMS,I found all of the room temperature was 2or 3degree higher than others floor.I also find out supply side AHU air pressure level was not enought .It sets 350pa ,however re
We check power is coming from switchbord.Power is coming from switchbord.Check indoor ,outdoor(before&after isolation). switch ).Open outside unit >>check voltage of compressor. No voltage,it might psc borad is not good.Check capacitor is enough p0w
Some of the chiller use R134A refrigerant. EVAP Rfgt pressure is 263kpag.However ,one of the chiller use R410 Rfgt ,succuction pressure is around1390kpa.That's is really surprised it.It is very hight pressure.
こちらの天井埋め込みエアコンのコントローラーが電源を入れても反応がしなくなり、また、こちらのエアコンのすぐ近くもう1個のエアコンがあり、以前は、よく隣のこのエアコンまで、そのコントローラーで反応してしまうため、今回一層の事、リモートコントローラーを備え付